Ed's Red

Ed's Red is a do it yourself bore cleaner.  It will cure everything from moles to sore assholes.

    It also contains enough Acetone it ought to take care of plastic fouling in short order. For me I caught Hoppes #9 on sale at Midway once and I've still got a half galon left.

CONTENTS: Ed's Red Bore Cleaner

1 part Dexron II, IIe or III ATF, GM Spec. D-20265 or later. 1 part Kerosene - deodorized, K1 1 part Aliphatic Mineral Spirits, Fed. Spec. TT-T-2981F, CAS #64741-49-9, or substitute "Stoddard Solvent", CAS #8052-41-3, or equivalent, (aka "Varsol") 1 part Acetone, CAS #67-64-1.

(Optional up to 1 lb. of Lanolin, Anhydrous, USP per gallon, OK to substitute Lanolin, Modified, Topical Lubricant, from the drug store)

MIXING INSTRUCTIONS:

    Mix outdoors, in good ventilation. Use a clean 1 gallon metal, chemical-resistant, heavy gage PET or PVC plastic container. NFPA approved plastic gasoline storage containers are also OK. Do NOT use HDPE, which is breathable because the acetone will evaporate. The acetone in ER will attack HDPE in about 6 months, making a heck of a mess!

    Add the ATF first. Use the empty container to measure the other components, so that it is thoroughly rinsed. If you incorporate the lanolin into the mixture, melt this carefully in a double boiler, taking precautions against fire. Pour the melted lanolin it into a larger container, rinsing the lanolin container with the bore cleaner mix, and stirring until it is all dissolved.

    I recommend diverting a small quantity, up to 4 ozs. per quart of the 50-50 ATF/kerosene mix for use as an "ER-compatible" gun oil. This can be done without impairing the effectiveness of the mix.

INSTRUCTIONS FOR USING Ed's Red Bore Cleaner:
 

  1. Open the firearm action and ensure the bore is clear. Cleaning is most effective when done while the barrel is still warm to the touch from firing. Saturate a cotton patch with bore cleaner, wrap or impale on jag and push it through the bore from breech to muzzle. The patch should be a snug fit. Let the first patch fall off and do not pull it back into the bore.
  2. Wet a second patch, and similarly start it into the bore from the breech, this time scrubbing from the throat area forward in 4-5" strokes and gradually advancing until the patch emerges out the muzzle. Waiting approximately 1 minute to let the bore cleaner soak will improve its action.
  3. For pitted, heavily carbon-fouled "rattle battle" guns, leaded revolvers or neglected bores a bronze brush wet with bore cleaner may be used to remove stubborn deposits. This is unnecessary for smooth, target-grade barrels in routine use.
  4. Use a final wet patch pushed straight through the bore to flush out loosened residue dissolved by Ed's Red. Let the patch fall off the jag without pulling it back into the bore. If you are finished firing, leaving the bore wet will protect it from rust for up to 30 days. If the lanolin is incorporated into the mixture, it will protect the firearm from rust for up to two years. For longer term storage I recommend use of Lee Liquid Alox as a Cosmolene substitute. "ER" will readily remove hardened Alox or Cosmolene.
  5. Wipe spilled Ed's Red from exterior surfaces before storing the gun. While Ed's Red is harmless to blue and nickel finishes, the acetone it contains is harmful to most wood finishes).
  6. Before firing again, push two dry patches through the bore and dry the chamber, using a patch wrapped around a suitably sized brush or jag. First shot point of impact usually will not be disturbed by Ed's Red if the bore is cleaned as described.
  7. I have determined to my satisfaction that when Ed's Red is used exclusively and thoroughly, that hot water cleaning is unnecessary after use of Pyrodex or military chlorate primers. However, if bores are not wiped between shots and shots and are heavily caked from black powder fouling, hot water cleaning is recommended first to break up heavy fouling deposits. Water cleaning should be followed by a thorough flush with Ed's Red to prevent after-rusting which could result from residual moisture. It is ALWAYS good practice to clean TWICE, TWO DAYS APART whenever using chlorate primed ammunition, just to make sure you get all the residue out.

Back to Index Page